If, say, your dryer sits in the basement, then the hose needs to make at least one turn. To complicate matters, the total length of the run should not exceed 25 feet—and that’s for a straight like Woosa shot. From that maximum, deduct five feet for 90-degree bends, and two and a half feet for 45-degree ones. If you need to undo any of your work, don’t be afraid to peel off the tape.
Measure, Cut and Assemble Vent
Remove the dryer and the old ventilation setup from the wall. This point is where you are most likely to need that dust mask. If you have seen my other guides, this would be the time I suggest safety gear. Thankfully, you probably only need a dust mask for what flies into the air. The only thing you need to be sure of is turning off the gas.
I’m a guy who becomes the expert of whatever I stumble upon, writing-wise. I’ve written tons about cool home products, home improvement, and smart technology in the home. I’m also the proud father of a kiddo born on new years, making my holidays very busy. Once the offset vent is in such a way where you feel comfortable, you can move onto the last step. Make sure that you do not make any major diversions from the approved construction plan to avoid penalties. Will ship within 7 business days of receiving cleared payment.
Attach the First Vent Section
I did have to use Nashua tape to seal the new duct to the elbows, but other than that it worked well. Regarding photo #2 where you shimmy the semi-rigid hose over the elbow duct. They are EXACTLY the same size, and I can’t fit the hose outside or inside the duct. I’m at risk of distorting the metal so much it’ll be useless, and I don’t have a crimper.
What type of dryer vent is best?
Tapping on the dryer duct while you do this will help knock off lint that’s stuck to the sides and joints. To avoid fires, vacuum lint from around dryer drums, burners and motors at the bottom of the cabinet. Wrap each fitting with yellow PTFE tape, looping around the fitting two or three times in a clockwise direction. Once wrapped, attach one end of the gas line to the dryer inlet fitting and hand tighten.
All connections are duct-taped for extra peace of mind. I’ve got two bathrooms where the fans exit into the attic and pump all the shower steam up there. I’d like them to exit under the soffits, as I’ve just had my entire roof replaced with a new sheet metal roof. You will need to turn the dryer on and get on top of the roof if you want to clean the rooftop vent. To get on top of the roof, you will need to use a ladder and make sure you do this safely. Let’s first see the reasons why venting a dryer through the roof is not advisable and how to do it properly if you have no other options.
Do this by securing the tube on the fittings that your dryer comes with and follow the instructions of the product as each dryer is different. The best way to vent a dryer is through the outside wall. Generally, it is not advisable to vent a dryer through the roof because it can cause moisture buildup and mold in the attic. And fire hazards due to blockage of roof vent and pipes as a result of lint collection. Some dryers are fueled by gas rather than electricity. Connecting gas hoses should be performed by a professional installer.
If you do not receive your package within the estimated delivery time, please drop us an email and we will investigate the matter immediately. We guarantee a 100% Full Refund if you do not receive your order. You should expect to receive your refund within four weeks of giving your package to the return shipper, however, in many cases you will receive a refund more quickly. Reproduction in whole or in part without permission is prohibited. Dryer vents can pose a significant fire risk if they aren’t set up properly, as this can make your machine work harder. Home Inspector Secrets is an online resource for owners, buyers, and sellers to understand all aspects of home maintenance.
A shorter hose also helps your dryer work more efficiently. Dryer hoses are made from flexible aluminum foil and steel wire. The hoses are flexible, so you have to bend them to run from dryer to vent. They’re also fire resistant and can endure the intense heat that dryers create.
We have detailed home guides, product reviews, inspection advice, and much more. In addition, make sure that the outside vent flap is working properly, opening when there is airflow, and closing when the dryer stops. The most important thing to know is that you may need an offset vent. To penetrate stucco or concrete, it’s easier to use a masonry bit to drill multiple holes around the circumference of the desired opening before manually chiseling out its interior. Don’t ever feel like you need to force a flexible hose in the back.
Tighten the hose clamp onto the semi-rigid duct and elbow. When it comes time to hire a pro to install your dryer vent, you have several options, and it typically depends on your specific needs. Connect the larger duct collar of the periscope vent to the back of the dryer duct. The wall vent may be above the dryer duct collar or it may be to one of the sides. A dryer vent installation can be a pain even if you do all the right things.
If there’s wood behind the masonry, you’ll also need a wood hole saw. There may be steel in there so make sure your hole saw are gonna get through what you need to get through… They have come down in price a lot and are much more efficient. You need a big ass masonry drill with a 4” hole saw masonry bit. We are tirelessly committed to providing a safe and secure online shopping experience so that you can shop with confidence. Please also note that the shipping rates for many items we sell are weight-based.